Engine

To ensure world-class quality our engines are all manufactured in the United Kingdom, Europe, United States of America or Japan

Alternator

All our alternators are UK sourced.

Radiator

All the radiators that we use in our generating sets are European manufactured.

Water Separator

Water contamination in fuel is separated out with the fuel/water separator.

Battery Cables

Heavy duty battery cables.

Manual Pack

Full functional manual pack supplied with all generating sets.

Circuit Breaker

Complete with power loom and Busbar connection point. (Not standard on 9 Series)

Medium Duty Air Cleaner

Removes contaminants in the air prior to entering the engine.

1 Phase AVR Sensing

Voltage sensing via one phase.

Emergency Stop Push Button

Allows you to quickly stop the generating set in case of an emergency. Pressing the emergency stop button causes the generating set to shut down immediately.

Coolant Solution

Standard 30% antifreeze supplied with all generating sets. Upgade for colder ambients available as an option.

Radio Frequency Interference Suppression Kit (AR6)

Minimises disturbances on the generators output from interference caused by non-linear loads. Also known as RFI.

Battery

InSight3100 Control Panel (PN31)

Basic automatic control panel with simple to use controls and numerical displays.

Upgrade Drive End Inlet from IP21 to IP23 Protection (AIP3)

Improved protection against moisture ingress.

Base Tank

This is a self contained fuel tank in base frame of generating set.

Fuel Tank Level Gauge

Visual fuel level to help monitor fuel.

Industrial Silencer

Fitted as standard on open generating sets.

InSight3300 Control Panel (PN33)

Automatic control panel with electronic engine support as well as expansion and remote communication capabilities.

Insight 4100 Control Panel (PM41)

Insight 4100 Digital Automatic Control Panel

Insight 3300 Remote Display (RP33M)

Insight 3300 Remote Display Panel (loose)

Insight4100 Remote Display (RP41M)

Insight 4100 Remote Display Panel (loose)

Remote Communications Solution for InSight3300/4100 (RC7D)

Remote communications plug-in module for Insight3300/4100 - Ethernet interface

Remote Communications Solution for Insight3300/4100 (RC7E)

Remote communications plug-in module for Insight3300/4100 - GSM/GPRS Wireless Remote Monitoring with antenna

Remote Communications Solution for Insight3300/4100 (RC7F)

Remote communications plug-in module for Insight3300/4100 - to support RS232 and RS485 Modbus RTU interfaces

Automatic Transfer Systems (ATS) (ATS)

To provide automatic control of your standby generating set in the event of a power outage. Available from 40A - 4000Amp.

Sound Attenuated Enclosure (CAESQ)

Fully galvanised steel enclosure delivering durability and security for your generating set.

Electronic Governor (EG1)

Accurately controls the engine speed. Recommended for synchronising. Standard on some models - Refer to factory.

Electronic Governor Programming Kit (GCK1)

Used to program or monitor the Woodward L series governor.

Coolant Heater (WH1)

Helps the engine to start in cold weather.

Lube Oil Drain (LV1)

Allows removal of lubricant during service or maintenance.

Lube Oil Drain Pump (LP1)

Assists in the removal of lubricant during service or maintenance.

Anti - Condensation Heater (AH1)

Appropriate when the generating set is to be sited in a low ambient and /or high humidity environment. The heater maintains the air around the windings at a suitable temperature to prevent winding corrosion due to condensation.

Programming Interface Kit (AP1)

Used to adjust setting on MeccAlte automatic voltage regulator.

Total Plus Winding Protection (AWP1)

This is the ultimate solution to be used when the application or the environment is abusing the insulation of the generating set. Also includes an over-coating of all the rotating active components.

Low Ambient Coolant Solution (WA2)

Coolant solution for ambients down to -36degC. 50% antifreeze.

Approaching High Coolant Temperature Alarm (WC2)

Automatic high coolant temperature alarm at pre-set temperature level. Available with InSight4000/6000 only.

Bunded Fuel Base Tank (BT1)

Secondary containment of fuel for leakage prevention.

Integral Single Skinned Tank (TI1/2/3)

Integral single skinned tank. (600, 1000, 1300 litres - canopied only)

Single Point Lift (BL1)

Eye hook fitted to top centre of canopy. Provides means of lifting generating set and is useful during installation. Available with canopied models only.

Captive Anti-Vibration Mounts (AV1)

Required for mobile generator applications.

Low Fuel Level Alarm (FL1)

Automatic alarm for approaching low fuel level.

Analogue Fuel Level Measurement (FM1)

Visual fuel level % display on controller. Not available with InSight3000.

Four Position Fuel Level Switch (FP4)

Gives fuel level indication at 4 set levels.

3 Way Dual Valve (BPV)

3 way dual valve with single lever operation. Complete with single lever operation. This should be used for remote fuel connection selection instead of basetank. Manual changeover between two fuel sources to the engine.

Industrial Silencer Mounting Kit (MK1 )

Essential kit for mounting an industrial silencer during installation. This kit is supplied loose and includes 2 x cuffed elbows, 2 x support brackets, 6 x clamps and 1 x rain cap.

Residential Silencer (ES1)

Provides additional exhaust noise reduction. Supplied loose. (Standard on all canopied sets)

Residential Silencer Mounting Kit (MK2)

Essential kit for mounting a residential silencer during installation. This kit is supplied loose and includes 2 x cuffed elbows, 2 x support brackets, 6 x clamps and 1 x rain cap.

Stainless Steel Bellows (EB1)

Provides flexible connection between engine and exhaust. Supplied loose.

4 Pole Circuit Breaker (CB4)

This is an upgrade from the standard 3 pole circuit breaker. The neutral connection is broken as well as L1, L2 and L3. (3 phase only)

Auxiliary Contact in Circuit Breaker (AUX1)

Provides the controller with an indication on the current circuit breaker position.

16A/ 32A/ 63A CEE Form Socket (SK0/1/2/3)

This is a ready to use socket supplied with the generating set. Equipment can be easily connected.

Battery Isolator Switch (BI1)

A lever is placed directly after the battery which is used to isolate the batteries from the machine

Battery Charger (BC1)

Keeps the genset starting batteries full of charge when the machine is not running. Includes BC failure. 5A 220/240 Volt

Battery Charger including Boost (BC2)

Keeps the genset starting batteries full of charge when the machine is not running. Includes BC failure and boost. 220/240 Volt

Sound Attenuated Container (CEC)

Increased sound attenuation with container option. Bespoke containers available throughout the range.

Tool Kit (TK1)

Basic maintenance tools.

Packing Case (PC1)

Adds additional protection to genset during shipping.

CE Certification - Open Sets (CE1)

Additional guarding on exhaust manafolds. Certificate of compliance.

CE Certification - Canopied Sets (CE2)

Certificate of compliance.

UKNI / CE Certification Open Sets (UKNI / CE 1)

UKNI / CE Certification - Canopied Sets (UKNI / CE 2)

Additional Operators Manual (OM1)

Additional operator manuals for workshop/service personnel.